DaisyCloudSeed
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Erwin Coumans.
gritwavev0.53.05 on GitHub
Custom firmware for the Electrosmith Daisy patch.Init() by Tobias Hienzsch.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Erwin Coumans.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Ewan Hemingway.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by algoritmarte.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Blue Nautilus.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Carl Colglazier.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Francesco Stablum.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Christian Colglazier.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by nnirror.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by house-of-houses.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by PaulBatchelor.
firmwaregithub.com
Mirth and Mirth Lite are alternate firmware for the Electrosmith Daisy patch.Init() that run neural-network audio models on the module. Patches load from a microSD card in three banks: amp captures built on Neural Amp Modeler's A2-Lite architecture, with drive into the network and a dry/wet mix; not-amps, captures altered inside the network, each with a single steer control that bends it toward wavefolding, rectifying, feedback, frozen or rate-reduced sounds; and neural models of two analog filters, a Doepfer Wasp and a Behringer Swords, with cutoff and resonance on knobs and resonance pushed into ringing and oscillation at the top of its range. Knob 1 sets the mix, knob 2 the steer amount or filter cutoff, knob 3 the resonance and knob 4 the drive, each summed with the CV jack beneath it. A press of the button moves to the next patch and a long hold to the next bank. Mirth uses a 64×48 OLED fitted in place of the toggle switch to show the patch, an input meter and processor load, while Mirth Lite runs on an unmodified patch.Init() and signals bank and patch with LED blinks. Capture files copied to the card are converted automatically at the next boot.
firmwaregithub.com
MultiOsc is alternate firmware for the Electrosmith Daisy patch.Init() that holds several synth voices in one image and lets the player choose one at power-up. The voices include a four-operator FM synth with parallel, serial and feedback algorithms; a dual oscillator with a quantized interval between its two voices, detune and pulse width, sent to separate outputs; and scanned synthesis, a simulated spring-mass string whose tension, damping and hammer strike shape an evolving drone or, with the envelope on, a gate-plucked note. Every voice shares one panel layout: a TUNE knob summed with V/oct, three MOD knobs with matching CV inputs, a trigger input and a single select button. A short press cycles the voice's algorithm, model or waveform, a long press switches between a play page and an edit page of secondary parameters with knob pickup, and a three-second hold returns to the voice chooser without a power cycle. It needs a 64×48 OLED fitted in place of the toggle switch, which shows the voice and the live meaning of each MOD control.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by Mike Perkowitz.
firmwaregithub.com
Custom firmware for the Electrosmith Daisy patch.Init() by house-of-houses.
No ratings yet — be the first to rate this patch.